Comtech-ef-data SDM-2020 Instrukcja Użytkownika Strona 202
- Strona / 234
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
SDM-2020 Satellite Demodulator Revision 4
Remote Control Commands MN/SDM2020D.IOM
A
–2
Commands are messages, which are transmitted to a satellite demodulator, while responses
are messages returned by a satellite demodulator in response to a command.
The general message structure is as follows:
• Start Character
• Device Address
• Command/Response
• End of Message Character
A.1.2 Start Character
A single character precedes all messages transmitted on the remote link. This character flags
the start of a message. This character is:
•
“<” for commands
•
“>” for responses
A.1.3 Device Address
The device address is the address of the one satellite demodulator which is designated to
receive a transmitted command, or which is responding to a command.
Valid device addresses are 1 to 3 characters long, and in the range of 1 to 255. Address 0 is
reserved as a global address, which simultaneously addresses all devices on a given
communications link. Devices do not acknowledge global commands.
Each satellite demodulator who is connected to a common remote communications link
must be assigned its own unique address.
A.1.4 End Character
Each message is ended with a single character, which signals the end of the message:
•
“cr” Carriage return character for commands
• “]” End bracket for responses
- Satellite Demodulato 1
- Installation and O 1
- Errata A 3
- Errata B 5
- Errata C 7
- SDM-2020 9
- Errata D 10
- Customer Support 12
- Table of Contents 13
- Preface MN/SDM2020D.IOM 14
- Figures 18
- Metric Conversion 22
- Trademarks 22
- Installation 24
- Warranty Policy 26
- Limitations of Warranty 26
- Exclusive Remedies 26
- Disclaimer 26
- Chapter 1. INTRODUCTION 27
- Mbps, with maximum 28
- 1.2 Assemblies 30
- 1.3 FAST Options 30
- 1.4.2 Transmit/Receive Data 32
- Chapter 2. INSTALLATION 35
- 2.2 Installation 36
- J3 PARALLEL J4 SERIAL J5 AUX 38
- Chapter 3. EXTERNAL 41
- CONNECTIONS 41
- 3.2 Connections 44
- 3.2.2 Fault Connector (J2) 45
- 3.2.3 Monitor Points (J21) 46
- 3.2.5 AC Power 47
- 3.2.6 Fuse Data 48
- 3.2.7 DC Power (Optional) 48
- 3.2.8 Ground (GND) or Earth 48
- SYSTEM TOPOLOGY (FAST) 49
- CHAPTER 4. FULLY ACCESSIBLE 49
- 4.1.1.1 Activation Procedure 50
- Select Features: 50
- Verify Upgrade 52
- Chapter 5. SPECIFICATION 53
- 5.2 BER Performance 58
- Specification 59
- 5.3 Data Rates 61
- 5.4 Fault Tree 62
- Chapter 6. FRONT PANEL 65
- OPERATION 65
- 6.1.1 Front Panel 66
- 6.1.2 LED Indicators 67
- 6.1.3 Front Panel Keypad 68
- 6.1.4 Menu System 69
- SDM-2020D 70
- MENU TREE 70
- IMPORTANT 105
- RX INTRF Firmware 107
- to set the baud 112
- to execute the change 114
- (Conditional) 116
- 6.1.13 Initial Defaults 122
- (see Note 4) 13 VDC 123
- (see Note 5) Off 123
- (see Note 5) 123
- 6.1.14 (C+N)/N to C/N and E 124
- Conversion 124
- Conversion Chart 125
- 7.2 Description 128
- 7.3 Configuration 130
- 7.3.1 User Interfaces 131
- 7.3.1.3 Auxiliary, J5 134
- Chapter 8. LOW VOLTAGE 137
- DIFFERENTIAL (LVDS) 137
- INTERFACE 137
- 8.1.2 Description 138
- 8.1.3 Configuration 139
- DEMODULATOR 140
- MODULATOR 140
- 8.1.4 User Interfaces 141
- 8.1.4.2 Auxiliary, J5 143
- 9.1.1 Applicable Documents 145
- 9.1.2 Description 146
- 9.1.3 User Interfaces 149
- 10.1.1 Applicable Documents 154
- 10.1.2 Description 154
- 10.1.3 Specifications 154
- 159
- 10.1.4.6 Terrestrial Timing 162
- 10.1.5.2 Faults 165
- 11.1.2 Description 168
- 11.1.3 Specifications 171
- 11.1.5.1 Buffer Size 176
- 11.1.5.2 Frame Structures 176
- 11.1.5.5 Buffer Centering 177
- interfere with 178
- 11.1.7 Test Modes 179
- 11.1.7.1 Interface Loopback 179
- Connectors J3, J4 & J6 180
- 12.1.2 Description 184
- 0.0 V ± 0.5 V 186
- 13.1.2 Description 192
- (see text) 193
- 13.1.3.1 Jumper Selection 195
- 13.1.4 Loopback Connection 197
- 13.1.5 Loop Thru 197
- Appendix A. REMOTE CONTROL 201
- COMMANDS 201
- A.1.2 Start Character 202
- A.1.3 Device Address 202
- A.1.4 End Character 202
- A.1.5 Command/Response 203
- RS-422 Interface 208
- LVDS Interface 209
- ASI/RS-422 Interface 209
- ASI/LVDS Interface 209
- SMPTE-310 Interface 210
- G.703 Interface 210
- ECL_HSSI Interface 211
- A.1.11 Configuration Status 214
- A.1.13 Stored Faults 220
- A.1.16 Data Interfaces 227
Powiązane produkty i podręczniki dla Ekwipunek Comtech-ef-data SDM-2020
(96 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.077 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji