Comtech EF Data SDM-309B Dokumentacja Strona 43
- Strona / 240
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Operation SDM-309B Satellite Modem
3–12 MN/U-SDM309B Rev. #
Data/AIS Data or Alarm Indication Signal. When Data_FLT is selected in the Interface
Configuration menu the fault indicates a Data stable condition. When AIS is
selected, the fault indicates data is all 1’s. Refer to Section 4.3 (Interface
Configuration for a detailed description of these faults.
FRM_BER Frame BER fault. Indicates that the frame BER exceeds 1E-3.
BW_ALM Backward Alarm Fault.
RX_PLL Receive Phase Locked Loop Fault.
Buff_Clk Activity detector alarm of the selected interface receive clock. The interface
will fall back to the satellite clock when this fault is active.
MUX_lock MUX lock fault. Indicates that the MUX is not locked.
3.1.7 Stored Faults
The Modem stores the first ten (Flt0 - Flt9) occurrences of fault status changes in each of
the six major fault categories. Each stored fault status change is stored with the time and
date of the occurrence. Stored faults may be viewed by entering the ‘stFaults” level from
the ‘sELECT” menu. All stored faults may be cleared by executing the “CLEAR ??
StFaults” command from the ‘stFaults” level.
Stored faults are not maintained through a controller power on reset cycle. However, the
last known time is maintained in non volatile RAM and upon power up a common
equipment fault is logged (Flt0) with that time and date. On power up an additional
common equipment fault is also logged (Flt1) to indicate the power up time and date. So
on power up the power down and power up times are logged as common equipment fault
0 and common equipment fault 1.
Upon entering the ‘stFaults” level use the left and right arrow keys to move between the
six fault groups and the “CLEAR ?? StFaults” selections. The time and date of the first
stored faults status (Flt0) for the selected group will be displayed alternately on line two
of the display. Use the up and down arrow keys to cycle through the selected group’s
stored faults status (Flt0 - Flt9). To display the faults status associated with the displayed
time and date press the “Enter” key, at this time you can use the right and left arrow keys
to move the flashing cursor to the fault you wish to identify.
To clear the stored faults currently logged simply press the “ENTER” key when the
“CLEAR ?? StFaults” selection is displayed.
Note: Faults are stored in time sequence with the oldest faults status change stored in
Flt0 and the most recent in Flt9. Only the first ten faults status changes are stored and all
stored faults which have not been used indicate “No Fault” on the display.
3.1.8 Utility
The utility functions provide a means to set the time and date of the modem real time
clock circuit. Provisions are also made for assigning data and code rates to the modulator
and demodulator. A lamp test function is provided for testing of the front panel optical
indicators.
- SDM-309B 1
- SDM-309BSDM-309B 1
- Warranty Policy 3
- Limitations of Warranty 3
- Exclusive Remedies 3
- Disclaimer 3
- About this Manual 4
- Cautions and Warnings 4
- Metric Conversion 4
- Trademarks 5
- Customer Support 6
- Table of Contents 8
- Rev. 0 vii 10
- Rev. 0 ix 12
- Chapter 1 14
- INTRODUCTION 14
- 1-1–2 MN/U-SDM309B Rev. # 15
- Figure 1-1 SDM-309B Modem 16
- 1-1–4 MN/U-SDM309B Rev. # 17
- MN/U-SDM309B Rev. # 1-1–5 18
- 1-1–6 MN/U-SDM309B Rev. # 19
- 1.4 System Specification 20
- 1-1–10 MN/U-SDM309B Rev. # 23
- MN/U-SDM309B Rev. # 1-1–11 24
- 1-1–12 MN/U-SDM309B Rev. # 25
- Chapter 2 26
- INSTALLATION 26
- Figure 2-1 Rear Panel View 28
- 2.2.1 Data I/O 29
- 2.2.2 Remote (J6) 29
- 2.2.3 Fault (J7) 29
- 2.2.4 IF Output (CP1) 30
- 2.2.5 IF Input (CP2) 30
- 2.2.6 AC Power 30
- 2.2.7 GND 30
- 2.3 System Requirements 30
- 2.4 System Installation 31
- Chapter 3 32
- OPERATION 32
- 3.1.3 Front Panel Controls 33
- Figure 3-1 Front Panel View 34
- 3.1.4 Configuration 35
- 3.1.4.1 MOD Configuration 35
- 3.1.4.2 DEMOD Configuration 36
- 3.1.5 Monitor 41
- 3.1.6 Faults 41
- 3.1.7 Stored Faults 43
- 3.1.8 Utility 43
- Figure 3-2 Menu Tree 47
- Figure 3-3 Menu Tree 48
- Figure 3-4 Menu Tree 49
- Figure 3-5 Menu Tree 50
- Figure 3-6 Menu Tree 51
- Figure 3-7 Menu Tree 52
- Figure 3-8 IF Loopback 53
- Figure 3-9 RF Loopback 54
- 3–24 MN/U-SDM309B Rev. # 55
- MN/U-SDM309B Rev. # 3–25 56
- 3.2.1 General 57
- 3.2.2 Configuration 57
- 3.2.2.1 MOD Configuration 58
- 3.2.2.2 DEMOD Configuration 59
- 3.2.3 Monitor 65
- 3.2.4 Faults 66
- 3.2.5 Stored Faults 67
- 3.2.6 Utility 68
- Figure 3-12 Menu Tree 71
- Figure 3-13 Menu Tree 72
- Figure 3-14 Menu Tree 73
- Figure 3-15 Menu Tree 74
- Figure 3-16 Menu Tree 75
- Figure 3-17 Menu Tree 76
- 3–46 MN/U-SDM309B Rev. # 77
- Chapter 4 78
- M&C AND INTERFACES 78
- Connect JP7 to RS232 79
- MN/U-SDM309B Rev. # 4-4–3 80
- 4.1.2.2 Remote Baud Rate 81
- 4.1.2.3 Remote Address 81
- 4.1.2.4 Battery 81
- 4.1.2.8 Utility Defaults 83
- 4.2 Digital Interfaces 83
- 4.2.1 IBS/M1200P Interface 84
- 4.2.1.2 Data Interface 84
- 4.2.1.3 Transmit Multiplexer 84
- 4-4–8 MN/U-SDM309B Rev. # 85
- MN/U-SDM309B Rev. # 4-4–9 86
- 4-4–10 MN/U-SDM309B Rev. # 87
- Figure 4-4 IBS Fault Tree 88
- Figure 4-5 Jumper Table 89
- 4.2.1.4 Receive Multiplexer 90
- 4-4–18 MN/U-SDM309B Rev. # 95
- 4.2.1.9.7 Send Data (J7) 98
- 4.2.1.9.8 Receive Data (J8) 99
- MN/U-SDM309B Rev. # 4-4–23 100
- 4-4–24 MN/U-SDM309B Rev. # 101
- 4.2.2.2 Data Interface 102
- 4.2.2.3 Transmit Multiplexer 102
- 4.2.2.7 Backward Alarm 103
- MN/U-SDM309B Rev. # 4-4–27 104
- 4-4–28 MN/U-SDM309B Rev. # 105
- MN/U-SDM309B Rev. # 4-4–29 106
- 4-4–30 MN/U-SDM309B Rev. # 107
- MN/U-SDM309B Rev. # 4-4–31 108
- MN/U-SDM309B Rev. # 4-4–35 112
- 4.2.2.10.11 Faults (J11) 115
- 4.2.2.11 Rear Panel Switches 116
- 4.2.2.11.1 Drop Data Input 116
- 4.2.2.11.2 Drop Data Output 116
- 4.2.2.11.3 Insert Data Input 116
- 4-4–40 MN/U-SDM309B Rev. # 117
- MN/U-SDM309B Rev. # 4-4–41 118
- Table 4-3 119
- MN/U-SDM309B Rev. # 4-4–43 120
- 4-4–44 MN/U-SDM309B Rev. # 121
- 4.3.1 Master/Slave 122
- 4.3.1.2 Master/Slave G.703 123
- 4.3.1.3 Master/Slave X.21 123
- 4.3.2 Master/Master 123
- Chapter 5 125
- THEORY OF OPERATION 125
- Figure 5-1 Modulator Card 127
- 5-5–4 MN/U-SDM309B Rev. # 128
- MN/U-SDM309B Rev. # 5-5–5 129
- 5.1.3 Theory of Operation 130
- 5.2.1 General Description 131
- MN/U-SDM309B Rev. # 5-5–9 133
- 5-5–10 MN/U-SDM309B Rev. # 134
- MN/U-SDM309B Rev. # 5-5–11 135
- 5-5–12 MN/U-SDM309B Rev. # 136
- MN/U-SDM309B Rev. # 5-5–13 137
- 5.2.3 Theory Of Operation 138
- 5.2.3.1 Demod Processor 138
- 5.2.3.2 Viterbi Decoder 138
- 5.3 Demodulator 139
- 5.3.1 General Description 139
- 5.3.2 Specifications 140
- Figure 5-9 Demodulator Card 141
- 5-5–18 MN/U-SDM309B Rev. # 142
- 5.3.3 Theory of Operation 143
- 5.4.1 General 143
- 5.4.2 Reacquisition 144
- 5.4.3 Fast Acquisition 145
- 5.4.4 Directed Sweep 145
- Chapter 6 146
- MAINTENANCE 146
- 6-6–2 MN/U-SDM309B Rev. # 147
- MN/U-SDM309B Rev. # 6-6–3 148
- 6-6–4 MN/U-SDM309B Rev. # 149
- Table 6-1 150
- 6-6–6 MN/U-SDM309B Rev. # 151
- MN/U-SDM309B Rev. # 6-6–7 152
- 6.1.4 Test Points 153
- Figure 6-6 154
- Figure 6-7 155
- Figure 6-8 156
- Figure 6-9 157
- 6.2 Fault Isolation 158
- 6.2.1 Modulator Faults 158
- 6.2.2 Demodulator Faults 159
- Table 6-2 162
- 6-6–18 MN/U-SDM309B Rev. # 163
- MN/U-SDM309B Rev. # 6-6–19 164
- 6-6–20 MN/U-SDM309B Rev. # 165
- MN/U-SDM309B Rev. # 6-6–21 166
- 6.4 Module Replacement 167
- 6.5 Module Identification 167
- 6.6 Repacking For Shipment 167
- Table 6-3 168
- Appendix A 169
- DATA RATES AND FILTERS 169
- 1.2 Variable Rate Filters 170
- MN/U-SDM309B Rev. # A–3 171
- A–4 MN/U-SDM309B Rev. # 172
- MN/U-SDM309B Rev. # A–5 173
- A–6 MN/U-SDM309B Rev. # 174
- MN/U-SDM309B Rev. # A–7 175
- A–8 MN/U-SDM309B Rev. # 176
- MN/U-SDM309B Rev. # A–9 177
- Appendix B 178
- SATELLITE MODEM REMOTE 178
- 3.4 End Character 179
- 3.1 Start Character 179
- 3.2 Device Address 179
- 3.3 Command/Responses 179
- 4.2.2 Demodulator Rate 183
- 4.2.4 RF Loop-back (ON/OFF) 184
- 4.2.5 IF Loop-back (ON/OFF) 184
- 4.2.7 Sweep Reacquisition 185
- 4.2.8 Fast Acquisition Mode 185
- 4.2.9 Sweep Center Frequency 185
- 4.2.10 Sweep Width Range 186
- 4.2.11 Sweep Direction 186
- 4.3.12 Interface Buffer Size 188
- 4.3.13 Transmit Data Fault 189
- 4.3.14 Receive Data Fault 189
- 4.3.15 Drop Data Format 189
- 4.3.16 Insert Data Format 189
- 4.4.1 Time Of Day 191
- 4.4.2 Date 191
- 5.3 Modulator Status 195
- 5.4 Demodulator Status 195
- 5.5 Common Equipment Status 196
- 5.8 Bit Error Rate Status 197
- 5.8.1 Raw BER 197
- 5.8.2 Corrected BER 197
- 5.8.3 Corrected BER Log 197
- 5.9 Eb/N0 Status 198
- 5.10 Modulator Rate Status 198
- 5.11 Demodulator Rate Status 198
- 5.13 Current Sweep Value 199
- 5.16 Stored Faults 199
- MN/U-SDM309B Rev. # B-B–23 200
- B-B–28 MN/U-SDM309B Rev. # 205
- 5.20 Change Status 206
- 5.21 Equipment Type 206
- B-B–30 MN/U-SDM309B Rev. # 207
- Appendix C 208
- EXTERNAL CHANNEL UNIT 208
- C-C–2 MN/U-SDM309B Rev. # 209
- MN/U-SDM309B Rev. # C-C–3 210
- C-C–4 MN/U-SDM309B Rev. # 211
- MN/U-SDM309B Rev. # C-C–5 212
- C-C–6 MN/U-SDM309B Rev. # 213
- MN/U-SDM309B Rev. # C-C–7 214
- C-C–8 MN/U-SDM309B Rev. # 215
- MN/U-SDM309B Rev. # C-C–9 216
- C-C–10 MN/U-SDM309B Rev. # 217
- 2.0 Digital Interfaces 218
- 2.1.1 Functional Description 218
- C-C–12 MN/U-SDM309B Rev. # 219
- MN/U-SDM309B Rev. # C-C–13 220
- C-C–14 MN/U-SDM309B Rev. # 221
- 2.1.2 Connector Pinouts 223
- 2.1.3 Specification 223
- 2.2 V.35 Interface 224
- 2.2.1 Functional Description 224
- MN/U-SDM309B Rev. # C-C–19 226
- C-C–20 MN/U-SDM309B Rev. # 227
- 2.2.2 Connector Pinouts 228
- 2.2.3 Specification 228
- 3.0 Front Panel Operation 229
- 3.1 Configuration 229
- 3.2 Monitor 232
- 3.3 Faults 232
- 3.4 Stored Faults 233
- 3.5 Utility 233
- Figure C-13 Menu Tree 235
- Figure C-14 Menu Tree 236
- Figure C-15 Menu Tree 237
- MN/U-SDM309B Rev. # C-C–31 238
- Appendix D 239
- SOFTWARE CHANGE 239
- SPECIFICATIONS 239
Powiązane produkty i podręczniki dla Networking Comtech EF Data SDM-309B
Networking Comtech EF Data DMD-2050E Dokumentacja
(342 strony)
(342 strony)
Networking Comtech EF Data SDM-650B Dokumentacja
(434 strony)
(434 strony)
Networking Comtech EF Data CDM-710G Dokumentacja
(136 strony)
(136 strony)
Networking Comtech EF Data CDM-800 Dokumentacja
(130 strony)
(130 strony)
Networking Comtech EF Data CDM-710L Dokumentacja
(172 strony)
(172 strony)
Networking Comtech EF Data CDM-710L Dokumentacja
(242 strony)
(242 strony)
Networking Comtech EF Data CIM-550 Dokumentacja
(460 strony)
(460 strony)
Networking Comtech EF Data CDD-880 Dokumentacja
(124 strony)
(124 strony)
Networking Comtech EF Data CDM-840 Dokumentacja
(244 strony)
(244 strony)
Networking Comtech EF Data SDM-100A Dokumentacja
(212 strony)
(212 strony)
Networking Comtech EF Data CDM-Qx Dokumentacja
(258 strony)
(258 strony)
Networking Comtech EF Data CDM-Qx Dokumentacja
(260 strony)
(260 strony)
AEG S2873DTS8 manuels
Manuels d'utilisation et guides de l'utilisateur pour Combi-frigo AEG S2873DTS8.
Nous fournissons des manuels en pdf 1 AEG S2873DTS8 à télécharger gratuitement par type de document : Manuel de l'utilisateur
Aeg S2873DTS8 Manuel de l'utilisateur (18 pages)
marque: Aeg | Catégorie: Combi-fridges | Taille: 0.34 MB |
Table des matières
Plus de produits et de manuels pour Combi-frigo AEG
| Modèles | Type de document |
|---|---|
| SD41240-4I |
Manuel de l'utilisateur
Aeg SD41240-4I User Manual [fr] ,
24 pages
|
| OEKOS2642-6KG |
Manuel de l'utilisateur
Aeg OEKOS2642-6KG User Manual [it] ,
22 pages
|
| S70312KG |
Manuel de l'utilisateur
Aeg S70312KG User Manual,
24 pages
|
| SK91240-4I |
Manuel de l'utilisateur
Aeg SK91240-4I User Manual [ru] ,
32 pages
|
| SANTO2632-6KG |
Manuel de l'utilisateur
Aeg SANTO2632-6KG User Manual [et] [sk] ,
20 pages
|
| SC71440I |
Manuel de l'utilisateur
Aeg SC71440I User Manual [nl] ,
14 pages
|
| SD91240-4I |
Manuel de l'utilisateur
Aeg SD91240-4I User Manual,
24 pages
|
| SC81840I |
Manuel de l'utilisateur
Aeg SC81840I Handleiding,
22 pages
|
| OEKOS2992-6I |
Manuel de l'utilisateur
Aeg OEKOS2992-6I User Manual [da] ,
28 pages
|
| SC81841-4I |
Manuel de l'utilisateur
Aeg SC81841-4I User Manual,
26 pages
|
| SD91240-4I |
Manuel de l'utilisateur
Aeg SD91240-4I User Manual [en] [fr] [ru] ,
24 pages
|
| SC91840-4I |
Manuel de l'utilisateur
Aeg SC91840-4I User Manual,
24 pages
|
| SANTO2733-6I |
Manuel de l'utilisateur
Aeg SANTO2733-6I User Manual,
28 pages
|
| S60240DT28 |
Manuel de l'utilisateur
Aeg-Electrolux S60240DT28 Handleiding [de] ,
76 pages
|
| SC81843-4I |
Manuel de l'utilisateur
Aeg SC81843-4I User Manual,
12 pages
|
| SKS78840F0 |
Manuel de l'utilisateur
Aeg SKS78840F0 User Manual [ro] ,
24 pages
|
| AGS58200F0 |
Manuel de l'utilisateur
Aeg AGS58200F0 User Manual [da] [fr] [pl] [sk] ,
20 pages
|
| SANTO2992-4I |
Manuel de l'utilisateur
Aeg SANTO2992-4I User Manual [pl] [sk] [ua] ,
24 pages
|
| S2492-4KG |
Manuel de l'utilisateur
Aeg S2492-4KG User Manual,
23 pages
|
| OEKOS.3250-6KG |
Manuel de l'utilisateur
Aeg OEKOS.3250-6KG User Manual,
12 pages
|
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.045 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji