Comtech EF Data Vipersat CDM-570 Podręcznik Użytkownika Strona 146
- Strona / 192
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Entry Channel Mode Switching
B-28 Vipersat CDM-570/570L User Guide
Note: Refer to the Vipersat SLM-5650A modem manual for Entry Channel
configuration setup. The text referenced within is similar between the
CDM-570/L and the SLM-5650A; the UI page appearances may differ,
however.
Figure B-15
STDMA Page with Entry Channel Mode, CDM-570/570L
Switching an ECM Remote from SCPC to STDMA
Use the following procedure to switch an ECM Remote operating in SCPC
mode back to STDMA mode.
Note: This switch must be performed manually.
1.
Click the Remote List menu item on the STDMA page shown in
figure B-15 above to display the STDMA Remote List shown in
figure B-16.
NOTE
NOTE
- CDM-570/570L 1
- User Guide 3
- COMTECH EF DATA 4
- Document Revision History 5
- Table of Contents 7
- Network Addressing 9
- Automatic Switching 9
- Dynamic Power Control 9
- ECM Migration 9
- Glossary 9
- L User Guide 10
- List of Figures 11
- Appendix A Figures 12
- Appendix B Figures 12
- Appendix C Figures 13
- List of Tables 15
- How to Use This Manual 17
- Conventions and References 18
- 1 - General 1-3 19
- Product Description 20
- Dynamic SCPC (dSCPC) 21
- Turbo Product Coding 22
- Header Compression 22
- Payload Compression 22
- Quality of Service 22
- Data Encryption 22
- New in this Release 23
- Customer Support 24
- QUICK START CONFIGURATION 25
- Initial Configuration 26
- Network Role 27
- Parameters 27
- Figure 2-3 29
- Figure 2-4 29
- Set the IP Address 30
- Configure the Route Table 31
- Figure 2-8 34
- Common Screen Commands 38
- Menu Descriptions 39
- Feature Configuration 41
- Vipersat Management 42
- Vipersat STDMA 42
- Vipersat Auto Switching 42
- Vipersat File Streamer 43
- STDMA Tx Rate 45
- Hub Type 46
- ECMv2 Mode 49
- Group ID 50
- STDMA Max Power Hunt 50
- Burstmap Multicast IP 51
- Outbound IP 52
- Cycles Per Burst Map 52
- Slot Guardband 53
- Slot Preamble Length 54
- Slot Data Length 54
- Total Slot Count 55
- Slot Cycle Length 56
- Slot Start in Cycle 56
- Set Remotes 56
- LNB LO Frequency 63
- BUC LO Frequency 63
- STDMA Statistics 64
- Show Hub Statistics 65
- Auto Switching 68
- Current WAN Transmit Mode 69
- ToS Switch Detection 70
- QoS Switch Detection 71
- STDMA Slot Capacity 76
- STDMA Switch Delay 76
- Percent Allocation 77
- SCPC Step Up Threshold 77
- SCPC Step Down Threshold 78
- SCPC Step Up Delay 78
- SCPC Step Down Delay 78
- SCPC Step Up Excess 79
- Time for Carrier Inhibit 80
- ToS Switching Parameters 81
- Hitless Switching Parameters 83
- SOTM Update 84
- Unit Role 85
- Expansion Unit 86
- Network ID 87
- Unit Name 87
- Receive Multicast Address 87
- Managing IP Address 88
- Management Security 89
- Primary Heart Beat 91
- Home State Revert 91
- Figure 3-74 92
- Figure 3-75 92
- DPC Enabled 93
- Calculate Max Power 93
- Target EbNo 95
- Speed Up EbNo 95
- Target DPC Address 96
- BaseLine Power 97
- DPC Offset 97
- SOTM Offset 97
- Force Modem to Home State 99
- STDMA State 99
- Transmit Frequency 99
- Transmit Data Rate 99
- Transmit FEC Type 100
- Transmit Coding Rate 100
- Transmit Modulation Type 101
- Transmit Power Level 101
- Transmit Enable 101
- Receive Frequency 101
- Receive FEC Type 102
- Receive Data Rate 102
- Vipersat Summary 103
- Vipersat Configuration 104
- Vipersat Migration 105
- UDP Port Base Address 105
- NETWORK ADDRESSING 107
- The OSI Reference Model 108
- Binary Math 110
- IP Addressing 112
- Private Network IP Addresses 114
- Subnet Mask 115
- Network Segments 116
- Default Gateways 117
- MAC Addresses 117
- AUTOMATIC SWITCHING 119
- Load Switching 121
- Burst Controller 122
- STDMA ACK Message 123
- Load Switching—STDMA Hub 125
- Hub Switching Process 126
- Load Switching—Remote 127
- Determination for Switching 129
- Load Switch Example 130
- Application Switching 133
- ToS Switching 135
- Configuration 137
- Example Implementations 138
- ToS Remarking 139
- ToS to DSCP Value Conversions 140
- Entry Channel Mode Switching 142
- Fail-Safe Operation 143
- Using STDMA ECM 145
- Figure B-15 146
- Dynamic Entry Channel Mode 148
- Hub Configuration 149
- Remote Configuration 150
- ECM Processing 151
- DYNAMIC POWER CONTROL 153
- Introduction 154
- STDMA mode 154
- Description 155
- Theory of Operation 156
- Figure C-2 158
- Main DPC Menu 161
- Enable DPC 162
- Target Eb/No 162
- Calculate Max Power Menu 163
- Max Power 166
- MODEM 167
- Power Considerations 168
- Cabling Considerations 168
- ECM MIGRATION 171
- Migration Procedure 173
- Configure Hub Unit 175
- Vipersat ECM Calculator 177
- GLOSSARY 179
- Appendix E - Glossary E-3 181
- Appendix E - Glossary E-5 183
- Appendix E - Glossary E-7 185
- Appendix E - Glossary E-9 187
- Appendix E - Glossary E-11 189
- Appendix E - Glossary E-13 191
Powiązane produkty i podręczniki dla Networking Comtech EF Data Vipersat CDM-570
Networking Comtech EF Data CDM-Qx Dokumentacja
(258 strony)
(258 strony)
Networking Comtech EF Data CDM-Qx Dokumentacja
(260 strony)
(260 strony)
Networking Comtech EF Data CDM-700 Dokumentacja
(266 strony)
(266 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.046 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji