Comtech-ef-data M&C Software Instrukcja Użytkownika

Part Number MN/M-C17.IOM Revision 3 M&C SoftwareMonitor and Control Software forComtech EFData Satellite TerminalsUser’s Guide

M&C Software Revision 3 Introduction MN/M-C17.IOM 1–2 MN/M-C17.IOM 1.2 Installation To install the program: 1. Remove the 3-1/2” diskette (c

M&C Software Revision 3 Revision 3 MN/M-C17.IOM MN/M-C17.IOM 1–3 1.3 Screen Descriptions The program uses five primary output screens. Each sc

M&C Software Revision 3 Introduction MN/M-C17.IOM 1–4 MN/M-C17.IOM Screen Description Terminal Mode Screen The Terminal Mode Screen allows the

M&C Software Revision 3 Revision 3 MN/M-C17.IOM MN/M-C17.IOM 1–5 1.5 Navigating The [F1] through [F5] function keys provide the basic mechanis

M&C Software Revision 3 Introduction MN/M-C17.IOM 1–6 MN/M-C17.IOM 1.6 Equipment Type Line At the very top of each of the first three screens

MN/M_C17.IOM 2–1 Chapter 2. OPERATION This chapter provides information regarding the operation of the M&C software when used with single or redu

M&C Software Revision 3 Operation MN/M_C17.IOM 2–2 MN/M_C17.IOM Figure 2-1. Initial Setup Screen Another important feature of the program is

M&C Software Revision 3 Operation MN/M_C17.IOM Rev. Revision 3 MN/M_C17.IOM 2–3 After the program has obtained the initialization data via the

M&C Software Revision 3 Operation MN/M_C17.IOM 2–4 MN/M_C17.IOM 2.2 Status Screen The Status Screen (Figure 2-3) provides the operating, mainte

M&C Software Revision 3 Operation MN/M_C17.IOM Rev. Revision 3 MN/M_C17.IOM 2–5 2.2.1 Changing a Parameter To change a parameter within this

M&C Software Revision 3 Operation MN/M_C17.IOM 2–6 MN/M_C17.IOM 2.2.2 Presentation of Fault Information The fault status portion of the Status

M&C Software Revision 3 Operation MN/M_C17.IOM Rev. Revision 3 MN/M_C17.IOM 2–7 2.3 Pre-Select Screen The Pre-Select Screen (Figure 2-4) prov

M&C Software Revision 3 Operation MN/M_C17.IOM 2–8 MN/M_C17.IOM 2.3.1 Programming a Pre-Select To program a pre-select with the current frequen

M&C Software Revision 3 Operation MN/M_C17.IOM Rev. Revision 3 MN/M_C17.IOM 2–9 2.4 Comm/Util Screen The Comm/Util Screen (Figure 2-5) is div

M&C Software Revision 3 Operation MN/M_C17.IOM 2–10 MN/M_C17.IOM 2.4.1 Communication Setup Sections The Communication Setup sections display t

M&C Software Revision 3 Operation MN/M_C17.IOM Rev. Revision 3 MN/M_C17.IOM 2–11 To command the program to “Acquire Comm”: 1. Press [↑] or [↓

M&C Software Revision 3 Operation MN/M_C17.IOM 2–12 MN/M_C17.IOM 2.5 Terminal Mode Screen The Terminal Mode Screen (Figure 2-6) allows the use

M&C Software Revision 3 Operation MN/M_C17.IOM Rev. Revision 3 MN/M_C17.IOM 2–13 2.5.1 Changing Baud Rate or Parity The terminal mode screen

M&C Software Revision 3 Operation MN/M_C17.IOM 2–14 MN/M_C17.IOM This page is intentionally blank.

MN/M_C17.IOM 3–1 Chapter 3. TROUBLESHOOTING This chapter provides detailed information on how to use the program to troubleshoot communication link p

Copyright © Comtech EF Data, 2000. All rights reserved. Printed in the USA. Comtech EF Data, 2114 West 7th Street, Tempe, Arizona 85281 USA, (480) 33

M&C Software Revision 3 Troubleshooting MN/M_C17.IOM 3–2 MN/M_C17.IOM The program will now display a flashing WORKING while it establishes a wor

M&C Software Revision 3 Troubleshooting MN/M_C17.IOM MN/M_C17.IOM 3–3 3.3 Communication with Redundant Systems All redundant systems serviced

M&C Software Revision 3 Troubleshooting MN/M_C17.IOM 3–4 MN/M_C17.IOM This page is intentionally blank.

METRIC CONVERSIONS Units of Length Unit Centimeter Inch Foot Yard Mile Meter Kilometer Millimeter 1 centimeter — 0.3937 0.03281

2114 WEST 7TH STREET TEMPE ARIZONA 85281 USA 480 • 333 • 2200 PHONE 480 • 333 • 2161 FAX

ii Customer Support Contact the Comtech EF Data Customer Support Department for: • Product support or training • Information on upgrading or retu

iii Table of Contents CHAPTER 1. INTRODUCTION ... 1–1 1.1 Requirement

M&C Software Revision 3 Preface MN/M-C17.IOM iv CHAPTER 3. TROUBLESHOOTING...

M&C Software Revision 3 Preface MN/M-C17.IOM v About this Manual This is the first edition of the manual. Supports software version 1.7 or great

M&C Software Revision 3 Preface MN/M-C17.IOM vi Reporting Comments or Suggestions Concerning this Manual Comments and suggestions regarding the

MN/M-C17.IOM 1–1 Chapter 1. INTRODUCTION The Comtech EF Data monitor and control (M&C) software is a DOS-based program designed to provide a user